Slip Hazards? Think Tough.

Think Grip. Think Dino Grip

items(s) | £0.00

Anti-Slip Landing Covers

Availability: In stock

(exc Tax)
Price From: Incl. Tax: £49.58 Excl. Tax: £41.32

* Required Fields

Dino Grip Landing Covers are a prefabricated FRP/GRP product, which give full anti-slip cover to the whole stair landing, with a contrasting coloured nosing. 

They offer extreme slip resistance and can also be installed onto a variety of stair substrates including traditional steel checker plate, which are notoriously slippery when wet.

Our Anti Slip Landing Covers are manufactured from Fibreglass to provide an extremely tough and durable product.  These types of products have been used in the most testing environments.  

Normally installed along with Stair Treads and Flat Sheet, Dino Grip Landing Covers are the ultimate choice for dealing with potential slip hazards to landing areas. Once installed, stair safety is instantly improved.


Available in three standard sizes and one width. Need a different size? Call us to ask about our FREE custom cutting service!

Disclaimer:

DinoGrip will not be responsible for shade or colour variation caused by application or substrate deficiencies, or fading resulting from natural causes such as weather.

  • Anti Slip
  • DIY Installation
  • Foot Traffic
  • Indoor Use
  • Outdoor Use
  • Screw Driver Attachment
  • Spring Loaded Rivet Gun
  • Anti Slip Surface
  • Hard Wearing, Tough & Durable
  • Contrasting Coloured Nosing
  • Installs over Virtually any Substrate
  • Choice of Sizes 
  • Black Yellow Nosing

Sizes

Dino Grip Landing Covers are available in a maximum 2400mm wide x 1200mm deep with a 55mm yellow nosing on the cover, and a 55mm yellow nosing down the riser.

Landing Covers

A - up to 1200mm
B - 55mm
C - up to 2400mm

Fixings

Stainless Steel Screws

Dino Grip provide our standard flanged stainless steel screws which are rust/stain resistant and eliminate any trip risk by sitting flush to the strip.  Our stainless steels screws are free of charge on all orders over £200. 

Colour Headed Screws

Alternatively Dino Grip can provide our colour headed flanged screws that are available in black to match the landing cover. 

The advantage of using these screws, is that they have a T-Star head which makes for easier installation, as the heads won't round off.

For metal surfaces, we would recommend rivet fixings.

Anti Slip

Dino Grip Landing Covers are a pre-formed fibreglass covers that has an anti-slip gritted top to provide an excellent slip-resistant and hard wearing surface in accordance with (BS7976 – 2)

Durable

Dino Grip Landing Covers are manufactured from FRP (Fibre Reinforced Plastic) / GRP (Glass-fibre Reinforced Plastic) to provide an extremely tough and durable product.

Corrosion Resistant

Dino Grip Landing Covers are resistant to a wide range of chemicals and is perfectly suited for use even in the harshest of environments. Chemical resistance guides are available on request.

Do it Yourself Installation

The versatility of Dino Grip Landing Covers allows it to be applied to almost any surface such as concrete, steel or wood. It is supplied as a finished product means that it can be walked on straight away after installation, keeping disruption to a minimum. 

Aesthetics

Dino Grip Landing Covers provide an instant aesthetically pleasing non-slip finish to any step or staircase surface landing.

Safety

When installing Dino Grip Landing Covers we would recommend that PPE (personal protective equipment) is worn.

Cutting the Landing Covers

If you need to cut the Landing Covers to size during your installation, we would recommend that a suitable dust mask with protective safety goggles and gloves are worn.  The Landing Covers should be cut externally or in well ventilated areas.

Dust residue can be disposed of using normal waste disposal methods. No special permissions or licenses are required.

Installation of Landing Covers

During the installation of the Landing Covers we would recommend that safety gloves and glasses are worn as the product has a textured anti-slip finish and whilst screwing the landing cover into place it is recommend that you wear safety glasses or goggles.

Preparation

Dino Grip recommend that the surface is firstly swept and cleaned ensuring that the surface is suitable to receive the Landing Covers. 

Installation

Wooden Surfaces

To lay the Landing Covers upon the surface and then use a 6mm masonry drill bit to drill the top of the gritted surface in the desired fixing locations.  We would recommend that there are 20 fixings per landing cover. 

Once the pilot holes have been drilled to then screw into position using the flanged stainless steel screws.

Additional adhesive can be used (if require) to add extra grip to the underneath the landing cover.

Metal Surfaces

To lay the landing cover upon the surface and then use a 6mm masonry drill bit to drill the top of the gritted surface only in the desired fixing locations.  We would recommend that there are 20 fixings per landing.  Change the drill bit to a 5.5mm metal drill bit.  Use drilling compound, and then proceed to drill the metal surface under the landing cover – the landing cover can be kept into position during this process as you have already pre-drilled the landing cover. 

Place rivet into hole and use a rivet gun to fix into position.  Please ensure that all rivets have been compressed. 

Additional adhesive can be used (if required) to add extra grip to the underneath of the landing cover.

Concrete Surfaces

To lay the landing cover upon the surface and then use a 6mm masonry drill bit to drill the top of the gritted surface and into the underlying concrete sub-base only in the desired fixing locations.  We would recommend 20 fixings per landing cover.  Remove the landing cover and re-drill the concrete fixing points with an 8mm masonry drill bit. 

Introduce raw-plugs into the holes in the concrete surface and place the Landing Covers into place.

Then screw into position using the flanged stainless steel screws.

Additional adhesive can be used (if require) to add extra grip to the underneath of the landing cover.

Additional Adhesive

Whilst mechanical fixings are all that is required to secure the landing cover, wherever possible, the application of an appropriate high strength gap filling adhesive will provide the following benefits:

A secondary fixing in the event that the mechanical fixings should fail.

A barrier against the "Drumming" noise that is created when fitting the landing cover over the existing substrate. Apply a 6mm bead of high strength gap-filling adhesive around the periphery of the landing cover and in horizontal stripes at approximately 200mm centres. Immediately press the landing cover firmly to the substrate to ensure adequate transfer of adhesive. A firm bond will be achieved in about one hour under normal circumstances and conditions. Secure with the mechanical fixings and allow the adhesive sealant to cure before allowing excessive traffic to use the areas.

RECOMMENDED MECHANICAL FIXINGS

Recommended fixings – based on a 1 metre stair tread.
Over Timber
No 20 x 4.8mm x 38mm – Flanged Stainless Steel Screws
Over Steel Plate
No 20 x 20mm Flanged headed rivets

Over Concrete

No 20 x Brown Raw Plugs (or equivalent)
No 20 x 4.8mm x 38mm – Flanged Stainless Steel Screws
Over Open Mesh
Stainless steel or zinc plated saddle clips and domed head bolts suitable in length for the depth of the existing treads.

CLEANING GUIDE AND TIPS

Whilst Landing Covers are extremely resilient to dirt and contaminations it will, as with most other things, become dirty.

Dry dirt and debris can easily be removed using a stiff brush and should be carried out on a regular basis.

If the Landing Covers have been subjected to spillages or the dirt has become embedded, detergents can be used. It is always advisable to test any cleaning product on the stair treads before starting the cleaning procedure. This can be done in an inconspicuous area of the installation.

Using the detergent, warm water and a suitable brush; scrub the affected areas until clean. The excess water can be removed using a wet/dry vacuum cleaner or power washer.

Where circumstances allow, the Landing Covers can be power washed without causing harm. Care should be taken when the Landing Covers has been stuck down and / or edge sealed as very high pressure power washing or repeated power washing could cause damage to sealants and adhesives.

GENERAL ROUTINE MAINTENANCE

The security of the fixings / adhesives should be checked on a regular basis. Circumstances will vary, based upon the volume of foot traffic etc. but, as a guide, monthly inspections would be advisable in high trafficked areas. 

Dino Grip landing cover is a high performance safety landing cover made from high quality GRP (glass reinforced plastic) / FRP (fibre reinforced plastic). They are designed to be installed on any flat surface to provide an instant non-slip surface.

CHARACTERISTICS

  • Slip Resistant Surface
  • Impact Resistant
  • Class 1 Flame Spread – Non Sparking
  • Corrosion Resistant
  • Lightweight
  • Non Metallic
  • Tough & Durable
  • Choice of Sizes
  • Quick Installation
  • Manufactured to ISO 9001

APPLICATIONS

Ideal for the installation on steps, fire escapes, all staircases, decking top surface, mezzanine floors and spiral staircases and for over-cladding onto worn surfaces.

TECHNICAL DATA

Description

Slip Resistant Decking Profiles

Top Finish

Carbon and Silicon Grip Top Surface

Stock Colours

Black with Yellow Nosing

Thickness

Nominally 4mm Thick

Chemical Resistance

Different Chemical Resistance Available, Please Call our Technical Department for Advice.

Panel Size

2400mm x 1200mm x 55mm Nosing

Landing Cover Weight

8.1kg

Service Temperatures

-20°c  to + 80°c

Load capabilities

Credited with no load bearing strength

Design Life

10+ Years (subject to traffic analysis)

General Use

Standard Pedestrian Traffic

SLIP RESISTANT LEVELS

Measured using the Pendulum test method (Four S rubber slider / 96 Slider) – standard simulated shoe sole.

Top Surface

Dry Reading

Wet Reading

Standard Grit Surface

80

75

The UK Slip Resistance Group guide to slip resistance of a floor for able bodied pedestrians.

Four S Pendulum Value

Potential for Slip

Above 65

Extremely Low

35 to 65

Low

25 to 65

Moderate

25 and Below

High

To ensure that the above slip resistant levels are maintained the Landing Covers should be kept clean in accordance with the attached cleaning guide and tips. 

Additional Information

Install Videos No
You may also like
Incl. Tax: £4.50 Excl. Tax: £3.75
Grip Fill
Incl. Tax: £3.60 Excl. Tax: £3.00
Brown Rawlplugs (Pack of 100)
Incl. Tax: £11.99 Excl. Tax: £9.99
Adhesive Gun
Incl. Tax: £39.00 Excl. Tax: £32.50
Metal Drill Bits 5mm (Pack of 5)
Incl. Tax: £10.79 Excl. Tax: £8.99
Metal Cutting Compound